Fusion Electronics Car Speaker CP AS1080 User Manual

8” SUPER SLIM ACTIVE SUBWOOFER  
CP-AS1080  
SPECIFICATIONS  
CP-AS1080  
Peak Power (Watts)  
Rated Power (Watts)  
Frequency Response  
Dimensions (mm)  
300  
100  
20Hz - 120Hz  
330(l) x 245(w) x 78(h)  
13 x 9-5/8 x 3”  
INSTALLATION GUIDELINES  
1. Ensure the +12V lead is disconnected from the battery before you connect any new equipment.  
2. Ensure the mounting location will not interfere with the gas tank, brake lines or electrical wiring.  
3. Ensure the Super Slim Active Subwoofer is securely fastened to the vehicle to prevent damage in the event of an accident.  
4. Ensure all wiring is protected to avoid pinching or crushing which could result in damage to the audio system.  
5. Ensure the mounting location has sufficient air flow around the amplifier.  
6. Ensure you use the recommended gauge wire/cable for all amplifier connections.  
WIRING  
POWER  
Ensuretheaudiosystemisturnedoffbeforemakinganyconnections  
Connect the power lead directly to the +12V battery terminal with  
to the amplifier, speakers or source unit.  
an inline fuse or circuit breaker as close to the battery as possible.  
Failure to do so could result in permanent damage to the audio  
system. When wiring the FUSION Super Slim Active Subwoofer  
ensure that the cable is protected from sharp objects and always  
use rubber grommets when wiring through metal panels.  
Ensure all terminals and connections are protected from the vehicle  
chassis, and from each other, as failure to do so could result in  
permanent damage to the audio system.  
LOW LEVEL INPUTS  
Choose the correct length RCA interconnects and run them to the  
RCA outputs of the source/head unit, avoiding running beside other  
looms and or power cable.  
Note: For correct performance both input RCA connectors must  
be used.  
FUSION Electronics recommends 8 gauge wire (power & ground).  
HIGH LEVEL INPUTS (SPEAKER LEVEL)  
GROUND  
If your head unit does not have RCA outputs, you can use the  
speaker outputs for the audio source for the CP-AS1080. Use the  
supplied cable and wire harness and connect the speaker outputs  
from the source to the high level Input. Be sure to observe polarity  
to avoid audio phase problems.  
Note: When using the high level connection, the Level MUST be set  
to minimum or the Subwoofer will be permanently damaged and  
could void your warranty.  
When grounding/earthing your Super Slim Active Subwoofer  
ensure that the location is a good source of ground (preferably the  
floor pan). Make sure the metal is clean of paint etc as a poor earth  
could damage your audio system.  
Note: This is the first connection to be made!!  
REMOTE TURN ON  
This connection turns the amplifier on and should be connected to  
the remote turn on wire from the Head Unit. If one is not available  
a switched 12V source must be used. Either a power antenna wire  
or ACC +12V.  
LOW LEVEL OUTPUTS  
Use the RCA output connectors to make one CP-AS1080 linkable  
to multiple CP-AS1080 Super Slim Active Subwoofers. This output  
is a pass-thru connection derived from the RCA input connector so  
the signal level and frequency response is the same as the original  
input signal.  

Blaupunkt ORLANDO CM127 User Manual
Bryan Boilers CLM 300 W GI User Manual
Bushnell Binoculars 111024ML User Manual
Canon 2685B001 User Manual
Canon Speedlite 380EX User Manual
Cateye CC 8000 User Manual
Dell Car Video System E2213H User Manual
Hypertec N16258PHY User Manual
JVC CD RECEIVER KD LHX502 User Manual
JVC GR DVX77 User Manual